top of page
Search
Round silver hairline joint aluminum column covers at a hotel entrance on Navy Pier in Chicago

How to Specify Metal Column Covers: A Section 05 58 13 Checklist

Writer: CNC Metalcraft
CNC Metalcraft
18 hours ago
4 min read

Column covers look simple on a reflected ceiling plan: a circle or a square around a structural column. In practice, a vague column cover specification is one of the quickest ways to get mismatched bids, a long RFI log and covers that do not fit. This checklist walks through what a specification should lock down, using the limits and options in the Sure-Panel® column cover specification (CSI Section 05 58 13) as the reference.

If you only need dimensions, start with the column cover sizing guide. If you want the whole system overview, see Sure-Panel® column covers.

1. Define the geometry first

Shape and size drive almost every other decision, so put them at the top of the section and on the drawings.

  • Shape: round, square, rectangular or a custom profile. Beam wraps are usually covered in the same section.

  • Diameter or face dimension: Sure-Panel® covers start at an 8 inch minimum diameter.

  • Height: the maximum single-piece length is 15 feet, round or square. Anything taller is built as stacked sections joined with a hairline or butt joint. Say on the drawings where you want that stack joint to fall, or tell the fabricator to locate it.

  • Vertical joints: round covers over 34 inches in diameter, and square covers over 26 inches, require vertical joints. If the design intent is a seamless look, the specification should say which joint type is acceptable at those seams.

Getting these numbers on paper early saves a redesign later. It also lets the fabricator flag a stack joint or extra vertical joint before bid day instead of after award.

2. Pick the material and thickness

The Sure-Panel® column cover specification lists four material families:

  • Painted aluminum: 3003-H14, .090" to .125".

  • Anodized aluminum: 5005 anodic quality, .090" to .125".

  • ACM: 4 mm or 6 mm, fire-retardant (FR) core.

  • Stainless steel: 304 or 316, 16 gauge.

Weight matters for handling and attachment. Approximate weights from the same specification: .090" aluminum 1.28 lb/sf, .125" aluminum 1.78 lb/sf, 4 mm FR ACM 1.56 lb/sf, 6 mm FR ACM 2.23 lb/sf and 16 gauge stainless 2.5 lb/sf.

As a general rule, solid aluminum plate is the usual choice where covers take abuse at pedestrian height, ACM suits larger flat faces and lighter assemblies, and stainless is chosen for a specific look or environment. Our ACM vs. aluminum plate guide covers the trade-offs in more detail.

3. Name the joint type

This is the line item most often left open, and it changes the look, the attachment and the maintenance. Sure-Panel® offers three:

  • Hairline joint: sections lock together through an internal key-slot system behind the face. Rough edges, fasteners, adhesives and caulk are concealed, and only a thin, consistent hairline shows.

  • Reveal joint: a dry-joint channel system with clips mechanically fastened to the panels and the substructure, and a "C" channel insert at each vertical reveal.

  • Caulk joint: mounting clips fastened to rout-and-return column legs and hard-fastened to the structure, with joints sealed with foam backer rod and silicone-based caulk.

Each joint type has its own 3-part specification. Pick one and reference it, rather than writing "manufacturer's standard joint."

4. Specify the finish

List the finish by type and color, and say whether a custom color match is required. Finishes in the Sure-Panel® column cover specification are PVDF/Kynar (standard), powder coat, anodized, brushed stainless, mill and primed. PVDF coil coatings are offered to AAMA 2605 or 2604. If you want help choosing, see our guide to metal panel finishes, or ask for samples.

5. Call out accessories and special conditions

Covers rarely stop at a plain cylinder. Make sure the specification and drawings show:

  • Capitals, bases, rings and reveals.

  • Perforation, if the cover is meant to be lit from inside.

  • Top and bottom conditions, including any top closure.

  • Interfaces with ceilings, floors, storefront and signage.

6. Describe the attachment and coordination

Attachment is the fabricator's design, but the specification should say who provides the substructure and what the cover attaches to. The Sure-Panel® Column Cover Installation and Storage Guide describes the general sequence for hairline covers: base angles at 24 inches on center maximum, PVC shims under the clips to separate dissimilar metals, clip angles set to the depth shown on the shop drawings, the top of the cover set 3/4 inch below the ceiling and the bottom ring 1/4 inch above the floor. Job-specific details and approved shop drawings always govern.

Those clearances are worth coordinating with the ceiling and flooring trades early so nobody is surprised at install.

7. Spell out submittals

At a minimum, most specifications ask for:

  • Shop drawings showing each cover, joint locations, stack joints and attachment.

  • Finish samples or color chips.

  • Product data for the material and coating.

  • Installation and storage instructions.

Sure-Panel® covers are drawn and fabricated by CNC Metalcraft® in Burnsville, Minnesota, so the shop drawings come from the same team that builds the covers.

8. Plan for lead time

Typical fabrication lead time is 3 to 4 weeks, or about 6 to 8 weeks when drafting (shop drawings) is included. Put shop drawing review in the schedule, because approval timing usually sets the delivery date more than fabrication does.

Where to get the specification

The Sure-Panel® hairline, reveal and caulk joint 3-part specifications (Section 05 58 13), plus the installation and storage guide, are free on the Specs & CAD page. CAD and Revit details are available on request.

Column cover specification FAQ

What CSI section covers metal column covers? Sure-Panel® column cover specifications are written in Section 05 58 13. Exterior metal wall panel systems such as the Sure-Panel® ACM rainscreen are written in Section 07 42 13.

What is the tallest single-piece column cover? 15 feet. Taller covers are built as stacked sections joined with a hairline or butt joint, like the 27-foot covers at Navy Pier.

Can I leave the joint type to the fabricator? You can, but bids will not be comparable. Naming hairline, reveal or caulk joint gives every bidder the same target.

Request a column cover quote

Send the column shape and size, height, quantity, joint type, material and finish, and any capitals, bases or rings. Call (952) 938-3356, email sales@sure-panel.com or use the contact page.

Related articles

 
 
 

Comments


(952) 938-3356

11901 Riverwood Dr, Burnsville, MN 55337

©2026 Sure-Panel® a CNC Metalcraft® Company

  • Instagram
  • LinkedIn
bottom of page